Lighting Research Center Lighting Research Center
    Volume 9 Issue 1
June 2006    
average rated life - The number of hours at which half of a large group of product samples fail under standard test conditions. Rated life is a median value; any lamp or group of lamps may vary from the published rated life. ballast factor (BF) - The ratio of the light output of a fluorescent lamp or lamps operated on a ballast to the light output of the lamp(s) operated on a standard (reference) ballast. Ballast factor depends on both the ballast and the lamp type; a single ballast can have several ballast factors depending on lamp type. color rendering index (CRI) - A rating index commonly used to represent how well a light source renders the colors of objects that it illuminates. For a CRI value of 100, the maximum value, the colors of objects can be expected to be seen as they would appear under an incandescent or daylight spectrum of the same correlated color temperature (CCT). Sources with CRI values less than 50 are generally regarded as rendering colors poorly, that is, colors may appear unnatural. rapid start - A method of starting fluorescent lamps in which the electrodes are heated prior to starting, using a starter that is an integral part of the ballast. Heating the electrodes before starting the lamps reduces the voltage required to strike the electric arc between the electrodes. A rapid-start system starts smoothly, without flashing. initial light output - A lamp's light output, in lumens, after 100 hours of seasoning. instant start - A method of starting fluorescent lamps in which the voltage that is applied across the electrodes to strike the electric arc is up to twice as high as it is with other starting methods. The higher voltage is necessary because the electrodes are not heated prior to starting. This method starts the lamps without flashing. It is more energy efficient than rapid or preheat starting, but results in greater wear on the electrodes during starting. The life of instant-start lamps that are switched on and off frequently may be reduced by as much as 25 percent relative to rapid-start operation. However, for longer burning cycles (such as 12 hours per start), there may be no difference in lamp life for different starting methods. correlated color temperature (CCT) - A specification for white light sources used to describe the dominant color tone along the dimension from warm (yellows and reds) to cool (blue). Lamps with a CCT rating below 3200 K are usually considered warm sources, whereas those with a CCT above 4000 K usually considered cool in appearance. Temperatures in between are considered neutral in appearance. Technically, CCT extends the practice of using temperature, in kelvins (K), for specifying the spectrum of light sources other than blackbody radiators. Incandescent lamps and daylight closely approximate the spectra of black body radiators at different temperatures and can be designated by the corresponding temperature of a blackbody radiator. The spectra of fluorescent and LED sources, however, differ substantially from black body radiators yet they can have a color appearance similar to a blackbody radiator of a particular temperature as given by CCT. mean light output - Light output typically evaluated at 40% of rated lamp life. In combination with initial light output, mean light output may be used to estimate lamp lumen depreciation. lamp efficacy - The ratio of the light output of a lamp (lumens) to its active power (watts), expressed as lumens per watt (LPW). color rendering - A general expression for the effect of a light source on the color appearance of objects in conscious or subconscious comparison with their color appearance under a reference light source. system efficacy - Also referred to as relative system efficacy, system efficacy is a measurement of a system'’s ability to convert electricity into light. Measured in lumens per watt (LPW), system efficacy is the ratio of the light output (in lumens) to the active power (in watts). lumen maintenance - The ability of a lamp to retain its light output over time. Greater lumen maintenance means a lamp will remain brighter longer. The opposite of lumen maintenance is lumen depreciation, which represents the reduction of lumen output over time. Lamp lumen depreciation factor (LLD) is commonly used as a multiplier to the initial lumen rating in illuminance calculations to compensate for the lumen depreciation. The LLD factor is a dimensionless value between 0 and 1. spectral power distribution (SPD) - A representation of the radiant power emitted by a light source as a function of wavelength. chromaticity - The dominant or complementary wavelength and purity aspects of the color taken together, or of the aspects specified by the chromaticity coordinates of the color taken together. It describes the properties of light related to hue and saturation, but not luminance (brightness). full-spectrum color index (FSCI) - A mathematical transformation of full-spectrum index into a zero to 100 scale, where the resulting values are directly comparable to color rendering index. An equal energy spectrum is defined as having an FSCI value of 100, a “standard warm white” fluorescent lamp has an FSCI value of 50, and a monochromatic light source (e.g., low pressure sodium) has an FSCI value of 0. gamut area - A measure of color rendering based upon volume in color space. It is the range of colors achievable on a given color reproduction medium (or present in an image on that medium) under a given set of viewing conditions. CIE - Abbreviated as CIE from its French title Commission Internationale de l'Eclairage, the International Commission on Illumination is a technical, scientific, and cultural organization devoted to international cooperation and exchange of information among its member countries on matters relating to the science and art of lighting. standard deviation - A measure of the average distance of a set of data points from their mean. A set of data points that are all close to their mean will have a smaller standard deviation than a set of points that are further from their mean. RE90 - Designation referring to lamps that use rare-earth phosphors and have color-rendering index values equal to or greater than 90. RE80 HLO, LL - An RE80 lamp with additional enhancements of high light output (HLO) and/or long life (LL). RE80 - Designation referring to lamps that use rare-earth phosphors and have color-rendering index values of 80-89. MacAdam ellipse - Researcher David L. MacAdam showed that a just noticeable difference (JND) in the colors of two lights placed side-by-side was about three times the standard deviation associated with making color matches between a reference light and a test light (MacAdam 1942, Wyszecki and Stiles 1982). These JNDs form an elliptical pattern of "constant discriminability" in a chromaticity space, centered on the chromaticity of a reference light, known as MacAdam ellipse. RE70 - Designation referring to lamps that use rare-earth phosphors and have color-rendering index values of 70-79. combined uncertainty - Combined uncertainty is calculated by finding the sum of the squares of sample random variability (standard deviation) and laboratory measurement uncertainty and taking the square root of that sum.
Conclusion

Many models of 32-watt T8 lamps are available with a variety of attributes. In principle, to help specifiers, T8 models could be separated into categories such as "good", "better", and "best" based on overall cost and performance. One way to divide T8 models into such categories would be to search for clear gaps in the reported values or to look for relationships where good performance in one category is associated with good performance in others.

Toward this end, NLPIP suggests that the CRI designations of RE70 and RE80 are justified as differentiators for "good" and "better" categories. RE70 models have generally good performance in light output, efficacy, and life, and have the lowest initial cost among T8 fluorescent lamp models. RE80 models could be considered a "better" category because they provide higher light output and efficacy, as shown in Figure 1 and Figure 4. With an appropriate luminaire layout or a lower ballast factor, RE80 lamps could provide a modest energy cost savings. The initial cost of RE80 models is marginally higher than RE70 models, but their power requirements are not much different. Since the cost of energy dominates the overall cost of a lighting system, there is little impact on operating costs for this "better" performance category.

A clear separation of RE80 models with enhanced attributes into a "best" (or "super") category is difficult to justify. Some RE80 models with a high light output attribute provide marginally higher efficacy; however, many of these lamps require more power to deliver higher light output. The higher electrical power required by these lamps will lead to a higher connected load and higher energy costs. Therefore, an appropriate luminaire layout or a lower ballast factor is imperative in order to take advantage of the small improvements in efficacy. For models offering a long life attribute, the uncertainties in lamp life are the largest among all the performance attributes, so there is a risk that these lamps may not last as long as expected. This is especially important considering that the initial cost of lamps with both attributes can be 100-300% more per lamp.

Previous
Previous
© 2006 Rensselaer Polytechnic Institute. All rights reserved.


Rensselaer Polytechnic Institute
LRC Intranet Web mail Lighting Research Center